– 10% now with the code BF10

New arrivals
0

Colour Rendering Index: What CRI Measures, and the R9 Figure the Box Leaves Out

Tips & advice

Matt black 118 cm LED batten pendant on two steel cables, lit in warm white above a light oak kitchen island with ripe red vine tomatoes, basil and parsley on a chopping board, a green glass bottle, a white plate and a terracotta tea towel

The colour rendering index, written CRI or Ra, scores out of 100 how faithfully a light shows colours compared with a reference source of the same colour temperature. The figure on the box is only the average of eight pastel samples: saturated red and the greens are left out. Aim for CRI 90 wherever you judge a colour.

Two bulbs side by side on the shelf: same wattage, same warm white, both marked CRI 80. Fit the first and the burgundy sofa turns brown, the tomatoes look cooked and your face in the mirror looks tired. The second would have left the room alive, and nothing on either box tells you which is which. Here is what the index measures, what it leaves out, and where to find the figure that does separate them.

What the colour rendering index measures, and how it is worked out

Standard colour samples are lit by the lamp under test, then by a reference source, and the shift between the two is measured. No shift, the index is 100; the bigger the shift, the lower it falls. The method is set by the International Commission on Illumination in its publication CIE 13.3-1995, and two of its details explain almost everything that follows.

The reference is not always the same light. Below 5,000 K it is a black body at the same temperature as the lamp, in other words the light of a glowing filament; above 5,000 K it is a phase of daylight. Either way, the reference has the colour temperature of the lamp being tested. That clears up the most common confusion: CRI says nothing about the tint of the light. A very yellow source can score 95 and a crisp white one only 80. Choosing between cool white vs warm white is a separate decision, made in kelvins.

Each sample gets its own score, worked out as 100 minus 4.6 times its colour shift: R1, R2, R3 and so on, and a very poor result can drop below zero. The general index printed on the pack, Ra, is the plain average of the first eight samples, and only those eight. Everything else in this guide comes back to that average. One more benchmark from colour science: a gap of about 5 points is roughly the smallest difference the eye notices between two lights, so CRI 82 and CRI 85 are, for you, the same lamp.

The R9 trap: what the average leaves out

The CIE method defines fourteen samples. The eight used for the general index are mid-saturation tints spread round the colour wheel, from greyish pink to pale violet. The other six are the hard colours, the ones that catch a lamp out, and none of them counts.

SampleWhat it stands forCounted in the CRI on the box?
R1 to R8Eight mid-saturation tints round the whole colour wheelYes, the CRI is their average
R9Saturated redNo
R10Saturated yellowNo
R11Saturated greenNo
R12Saturated blueNo
R13Light skin toneNo
R14Leaf greenNo

Read the exclusions again: the deep red of an armchair, the green of a houseplant or an olive wall, your own face in the mirror. A lamp can render all three badly and still show 80 legitimately, because its eight pastels are fine. That is how the index is defined.

For LED and OLED light sources, the product information sheet must give the R9 value separately, both under the British regulations and in the European product database, EPREL, which is public. Our team picked fifty EPREL sheets at random by registration number on 16 October 2026; on 17 October we checked each value again against the database, and 48 were still published.

CRI declaredSheetsLowest R9Highest R9Median R9
8027minus 9804
81 to 8911minus 32310
90 and above878050
Bar chart of the R9 value declared on four EPREL product sheets that all state a colour rendering index of 80: minus 9 for bulb A, 0 for bulb B, 14 for bulb C and 80 for bulb D
Four LED sources from the European EPREL database, all declaring CRI 80. Their rendering of saturated red runs from minus 9 to 80, yet the box of bulb A and the box of bulb D show the same figure.

Twenty-seven sheets declare exactly 80. Their median R9 is 4: half of these lamps render almost no saturated red, and eight are at zero or below. Yet one of them, with the same 80 on the label, declares an R9 of 80, and nothing on the box gives the difference away. From CRI 90 the median R9 rises to 50, but one sheet still shows 7. A high CRI makes a good R9 likely, never certain: if red matters in your home, look the value up.

Greens are worse off: neither saturated green nor leaf green is counted, and no sheet has to publish them. That is why the same wall changes character from one bulb to the next, as our guide to what colour goes with green shows. In a green room, the general index is not enough on its own. It matters just as much with the greyed sages and blues sold as calming colours, the shades a warm bulb changes most.

What 80, 90 and 95 look like once the light is on

The floor of 80 is not a marketing habit, it is the law. In Great Britain, the Ecodesign for Energy-Related Products and Energy Information (Lighting Products) Regulations 2021, S.I. 2021/1095, have required a CRI of at least 80 since 1 October 2021 (Schedule 3, Table 5). Two exceptions: discharge lamps above 4,000 lumens, and light sources meant for outdoor, industrial or other uses where lighting standards accept less, provided the packaging says so clearly. In Northern Ireland the EU ecodesign regulation still applies under the Windsor Framework, with the same floor. A bulb sold for indoor use is therefore at 80 or above by construction.

So the real question is never 70 or 80, but 80 or 90. With the 5-point rule in mind, the bands read easily.

CRI on the boxWhat you actually seeWhere it is enough
80 to 84Pastels and neutrals look fine. Reds fade, warm wood drifts towards grey, greens all look alike.Hall, landing, loft, utility room
85 to 89A visible step up on a fabric or a coloured wall, mostly when you compare two rooms side by side.Bedroom, living room with pale walls
90 to 94Saturated colours come back. The first level where a red stays red and a skin tone looks believable.Kitchen, wardrobe, bathroom mirror, a strongly coloured room
95 and aboveHard to tell from 90, except on two very close shades placed side by side.Sewing, painting, a hobby bench

Our reading: going from 80 to 90 changes the room, going from 90 to 95 changes a task. Paying extra for 95 in a sitting room makes little sense; paying it for the light over a craft table does.

Where CRI really matters, and where it changes almost nothing

The useful question is not which CRI for this room, but whether you judge a colour there. On a landing you judge a step and a distance. At a mirror or a chopping board you judge a shade, and you act on what you see.

Room or taskWhat you judge by eyeCRI we advise
Wardrobe, dressing areaThe colour of a garment, whether two pieces match90, or 95 with many close shades
Kitchen worktopWhether meat is cooked, whether vegetables are fresh90
Bathroom mirrorSkin tone, make-up, hair colour90
Sewing, painting, craftsOne shade against another95
Strongly coloured wall, sofa or rugThe depth of the colour you chose90
Hall, stairs, landingNothing, you are passing through80 is enough
Garage, loft, utility roomNothing either80 is enough
Matt black LED blade wall light, 50 cm tall with its small base box, lit in warm white on an off-white bedroom wall between a white panelled door with its light switch and an open oak wardrobe holding an olive jumper, a brick red shirt, a navy jacket, an ecru shirt and a mustard scarf
Our LED blade wall light, shown at its real 50 cm beside a standard switch plate, declares CRI 90 in warm white. Next to a wardrobe it gives the wall an evening glow; to tell olive from khaki, the light also has to reach the rail itself.

In a wardrobe, the classic mistake is to add brightness instead of quality: a rail flooded by a CRI 80 source still will not tell olive from khaki, and our guide to wardrobe lighting covers it in full. In front of a painting it works the other way: the amount of light has to stay modest to protect the pigments, so quality is all you have left, and our guide to picture lights gives the distances. On a bookcase, the spines form a colour chart that a mediocre CRI flattens into one dull band, the starting point of our guide to bookcase lighting.

Over a worktop, the fitting matters as much as the source. A continuous line hung along the worktop, like our LED pendant lights, lights the chopping board without your shoulders casting a shadow on it. The 118 cm LED batten pendant on this page gives 3,640 lumens at CRI 90, in 3000 K or 4000 K. In a room painted a deep colour, the square LED frame chandelier, 80 by 80 cm, also declares CRI 90 in warm white.

Reading the CRI on the box, the product information sheet and EPREL

On a bulb sold in its own box in Great Britain, the CRI must be printed on the packaging, rounded to a whole number (S.I. 2021/1095, Schedule 3, paragraph 6). Unlike the lumens and the colour temperature, it does not have to face you on the shelf, so turn the box over. You will meet it in three forms.

  • Stated in full. CRI 90, Ra 90 or Ra > 90 all mean the same thing: CRI is the everyday name, Ra the technical name of the general index.
  • As a three-digit code. A marking such as 830, 930 or 940 packs in two figures: the first digit gives the tens of the CRI, the next two the colour temperature in hundreds of kelvins. 830 reads as CRI 80 to 89 at 3000 K, 940 as CRI 90 to 99 at 4000 K. It is a manufacturers’ code inherited from fluorescent tubes, and no rule obliges anyone to use it.
  • Not at all. The usual case on a fitting with built-in LEDs: the rules only ask its instructions to state the energy class of the light source inside. Look at the product page, or ask the seller.

The richer document is the product information sheet. Its supplier must publish it free of charge on its own website, on a page with nothing else on it, and online sellers of bulbs must show it, or a link labelled “Product information sheet”, near the price. It gives the CRI and, for LED and OLED sources, the R9, with the useful luminous flux and the on-mode power. The QR code on a British energy label leads to that supplier page, not to a public register. In Northern Ireland, bulbs carry the EU label and are listed in EPREL, which anyone can search.

In practice: two bulbs both showing CRI 80, two sheets, two R9 values, and the choice is made. For a fitting with integrated LEDs, where the source cannot be swapped later, ask the question before you buy: our LED lights show the CRI on their product page whenever the manufacturer documents it.

A higher CRI costs a few lumens

There is a physical reason why CRI 90 has not become the norm everywhere. A standard white LED is a blue chip coated with a phosphor that turns part of the blue into yellow. The mix looks white but is short of deep red, which is exactly what drags R9 down. To fill that gap the maker adds a phosphor that emits in the deep red, where the eye is far less sensitive than in the green: the same energy yields fewer lumens. The spectrum improves, the efficiency drops.

The regulations put a figure on that trade-off, the only public and checkable one we found. In Schedule 3 of S.I. 2021/1095, the maximum power allowed for a given light output is multiplied by a CRI factor equal to the CRI plus 80, divided by 160. A CRI 80 source gets a factor of 1.00, a CRI 90 source 1.06. In plain terms, the rules let a CRI 90 lamp use about 6% more power than a CRI 80 lamp for the same light output. That is the order of magnitude on your bill.

We found no independent public measurement of the real loss in lumens per watt between two comparable products at 80 and 90; the figures that circulate come from sales literature. The sound method is to divide the useful luminous flux by the on-mode power on two product information sheets. That on-mode power, in real watts, is also the figure to compare with the maximum marked on a fitting, the key to whether you can use a 60 W bulb in a 40 W lamp. Our lumens to watts chart gives the equivalents, and our guide how many lumens do I need tells you how much light to plan before you compare anything.

Our method in three questions

Do I judge a colour here? If not, the default CRI 80 is fine, and your budget is better spent on lumens or on where the lights go.

Which colour, exactly? For a red, a warm wood or a skin tone, ask for the R9 as well as the CRI. For a green, take 90 at least, since the general index measures no saturated green.

Is the figure written anywhere? Our advice: when the value appears neither on the box, nor on the product page, nor on the product information sheet, assume 80 and decide from there.

In short, CRI is chosen room by room: 90 over the worktop and in the wardrobe, 80 on the landing and in the garage.

Colour rendering index: frequently asked questions

What is a good colour rendering index?

For a home, 90 or above wherever you judge colours: the kitchen worktop, the wardrobe, the bathroom mirror, a strongly coloured room. 80, the legal minimum for most bulbs in Great Britain, is enough for a hall, a landing or a garage. Above 95 the gain only shows on very close shades.

Is a CRI of 90 good?

Yes, for almost every room in a home: it is the first level where reds, warm woods and skin tones look believable. Check the R9 on the product information sheet too: in our survey of EPREL sheets, R9 at CRI 90 and above ran from 7 to 80, with a median of 50.

What does a CRI of 85 mean?

That the eight pastel test samples shift only a little, one step above the legal minimum of 80. A gap of about 5 points is close to the smallest difference the eye notices, so 85 looks slightly better than 80 and clearly short of 90 on saturated colours. It suits a bedroom or a pale living room.

Can you tell the difference between 80 and 90 CRI?

Yes, ten points show clearly. At 80, pastels look fine but saturated colours fade and greens look alike; at 90, reds, warm woods and skin tones become believable again. In return, the rules allow a CRI 90 lamp about 6% more power than a CRI 80 lamp for the same light output.

Which lamps have a CRI of 100?

Filament and halogen bulbs come closest, because below 5,000 K the reference source of the index is a glowing black body, which a filament closely resembles. Most have now gone from the shops. Among LEDs, sources above 95 are specialist products: in our sample of 48 EPREL sheets, only one declared a range reaching 100.

Is CRI the same as colour temperature?

No, they are two separate measurements. Colour temperature, in kelvins, describes the tint of the light, from warm yellow to bluish white. CRI describes how faithfully that light shows colours, compared with a reference of the same colour temperature. A very warm light can score 95 and a crisp white one only 80.

Sources

  • CIE 13.3-1995, Method of measuring and specifying colour rendering properties of light sources: eight test samples for the general index, six more (saturated red, yellow, green and blue, light skin, leaf green), special index of 100 minus 4.6 times the colour shift. International Commission on Illumination
  • The Ecodesign for Energy-Related Products and Energy Information (Lighting Products) Regulations 2021, S.I. 2021/1095: Schedule 3 (CRI factor, Table 5 minimum of 80, CRI on the packaging), regulation 12 and Schedule 8, Table 6 (product information sheet, R9), Schedule 11 (online sales). legislation.gov.uk
  • Regulation (EU) 2019/2020 and Delegated Regulation (EU) 2019/2015, applicable in Northern Ireland; EPREL product database, 48 light source information sheets checked on 17 October 2026. European Commission
  • Color rendering index (English edition), Indice de rendu des couleurs (French edition, a 5-point gap close to the smallest perceptible difference, after R. Sève, Science de la couleur, 2009) and Lichtfarbe (German edition, three-digit lamp colour code). Wikipedia

Related products

Modern Living Room Chandelier

Modern LED ceiling chandelier in metal in fireworks style

£79.99
Round LED wall light in silver aluminium, switched on, casting a spiral of warm light on a white wall
LED Wall Lights

Circular LED wall light in aluminium with light projection

£33.49
Scandinavian Pendant Light

Modern drop-shaped pendant light

£79.99

See also

Tips & advice
Tips & advice
Tips & advice
Discover more posts
Free delivery

From £65 purchase in selected countries*

14-day withdrawal period

14 days to return your product(s)

Customer service 5/7

Our team is available to answer your questions from 10am to 7pm

Secure payment

Every payment made on our online store is 100% secure